Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Manish

Pages: 1 [2]
16
NXPTM LPC2XXX and LPC17XX / Re: boot loader support in LPC2388
« on: October 16, 2009, 11:43:53 AM »
Good morning Mark,



  We have done z_upload.bin as per you have suggested but still new application not uploading because we are checking file in z.bin file in dir using FTP promp it is display M.BIN so we cant understood how this happen?. we have also seen that there is bootloader for USB but not for FTP ot webbased. so can you explain me why this?
 
 if we want open M.BIN file , read those file and uploading using fnDownload(Debug.c)  function. is this possible?.

Thank you
Manish Dabhi

17
NXPTM LPC2XXX and LPC17XX / Re: boot loader support in LPC2388
« on: October 08, 2009, 06:12:45 AM »
Good morning Mark,

I have problem with uploading with more then two so ,i have attached file in this Post.

Thanks
Manish Dabhi

18
NXPTM LPC2XXX and LPC17XX / Re: boot loader support in LPC2388
« on: October 08, 2009, 06:11:33 AM »
Good morning Mark,

I have problem with uploading with more then two so ,i have attached file in this Post.

Thanks
Manish Dabhi

19
NXPTM LPC2XXX and LPC17XX / Re: boot loader support in LPC2388
« on: October 08, 2009, 06:07:18 AM »
Good morning Mark,

Keil Uvision generate Hex file as well bin file. I have attach two individual compiled hex file and bin file along with uv setting. Please check it and if it has any problem then suggest me.

I hadn't problem with generating two file. It is generated from uTaksercombile.exe.

 How can i combine bootloader and application bin or Hex file? I have clear with uploading new bin file, but I have at initially. so please help regarding this.

Thanks
Manish Dabhi

20
NXPTM LPC2XXX and LPC17XX / for getting SP3
« on: October 07, 2009, 06:02:20 AM »
Dear All,

 I had download new service pack 3 but when I try to unzip, it want password, can anybody tell me password?

Regards,
MD

21
NXPTM LPC2XXX and LPC17XX / Re: boot loader support in LPC2388
« on: October 07, 2009, 05:56:28 AM »
hi Mark,

 I have two code in uTasker version1.4, one is Bootloader code and onther is Application code.
 As per your reply  I had compiled bootloader code and application code in Keil compiler. but when I was trying to combine both code's hex file it cant generate bin file. When I try to convert from bin to hex, it cant convert also. so please help regarding this.

And one problem to in Application programe I had seen that there is no support to download file new application file in FTP. so can you tell me how can i will do?

22
NXPTM LPC2XXX and LPC17XX / USB imlemnetation
« on: October 02, 2009, 09:57:18 AM »
Dear mark,

 I want to implement USB device in LPC2378 hardware, but when I have enable USB_INTERFACE macro then it gives error USB_HW. and It cant enable to anywhere so can help me on this ?

Thank you
Manish Dabhi

23
NXPTM LPC2XXX and LPC17XX / boot loader support in LPC2388
« on: September 26, 2009, 10:34:49 AM »

 Hi All,
I am new for utasker. can anybody help for how to downloading bootloader and application code in to lpc controller. I am compiling code using Keil and till downloading code using Flash Magic. what kind of utility required for downloading bootload code and application code.

Thanks
Manish


Pages: 1 [2]